Troubleshooting Blown Vehicle Fuses Every Time Trailer is Connected
Question:
I keep blowing fuses on my truck when I plug my trailer in. The turn signals and brake lights will still work but no running lights
asked by: Joseph S
Expert Reply:
It sounds like there is a short somewhere along the wiring of your vehicle or trailer that is causing a fuse to blow every time you connect.
The first thing I recommend doing is disconnecting the trailer and using a circuit tester like # PTW2993 to test the vehicle side connector. You can have a buddy run through the functions from inside the vehicle while you test each pin on the connector. If you detect any power to a circuit when there should not be any, then you know there is a short somewhere on the vehicle side. Simply trace along the wiring and look for any exposed areas that might be touching bare metal.
Also check that both the vehicle side and trailer side connectors are free of dirt and corrosion. If the connector is corroded or dirty, it can cause excess power draw and blow a fuse. Simply clean out as needed.
If everything checks out fine on the vehicle side, then you will want to check along the wiring for the trailer, again looking for any damaged or exposed wiring. You can also test the trailer wiring for function by connecting each wire to a 12V battery. Lastly, make sure that the main trailer connector ground and all the light grounds are securely attached to clean bare metal surfaces.
If you are unable to find the issue, please let me know and I will be happy to look into this further.
Ge
3/25/2020
Good morning my trailer battery fuse keeps blowing any suggestions where I can look?
Product Page this Question was Asked From
Continue Researching
- Shop: Viair 7-Way Automatic RV Portable Air Compressor for Class C RVs - 150 psi - 2.30 cfm
- Search Results: galvanized axle
- Shop: Conventional Ramp Door Spring for 7' Wide Enclosed Trailer - Single Spring - 120-lb Capacity
- Shop: Trailer Wiring
- Shop: Viair Automatic RV Portable Air Compressor for Class C RVs - 150 psi - 2.30 cfm
- Article: Troubleshooting 4 and 5-Way Wiring Installations
- Search Results: galvanized axles
- Q&A: What Would Happen if Trailer Brake Assemblies Were Installed On Wrong Side of Trailer
- Q&A: Incorrectly Installed Brake Assemblies on Dual Axle Camper
- Shop: Replacement Side Marker Lens for Optronics STL16RB and STL17RB Tail Light
- Shop: Replacement Side Marker Lens for Peterson Tail Lights for Trailers Over 80" Wide
- Shop: Conventional Ramp Door Spring for 8' Wide Enclosed Trailer - Single Spring - 150-lb Capacity
- Shop: AMPLock Trailer Coupler Lock for Square, 2-5/16" Ball Couplers - Ductile Cast Iron
- Search Results: 362sa7218
- Search Results: 362sa6
- Shop: Vehicle Tow Bar Wiring
- Article: Trailer Wiring Diagrams
- Video: Review of Optronics Trailer Lights - GloLight LED Trailer Tail Light - STL111RMB
- Search Results: powered converter
- Video: Curt T-Connector Vehicle Wiring Harness Installation - 2010 Ford Escape
- Video: Optronics Trailer Lights - License Plate Lights - LPL11CB Review
- Video: Optronics Trailer Lights - Clearance Lights - MCL22RK3B Review
- Video: Optronics Trailer Lights - Clearance Lights - MCL121RK9PVG Review
- Video: Optronics Trailer Lights - Clearance Lights - MCL11CRKB Review
- Video: Review of Optronics Trailer Lights - Clearance Lights - MCL10RKB
- Q&A: Trailer Running Lights Keep Blowing Fuses when Turned On
- Q&A: What Clearance Lights do You Recommend that Do Not have the Brake Light Function?
- Q&A: How To Install Mini LED Identification Light Kit for Trailers
- Search Results: heat shrink butt connector
- Search Results: jacketed 2 wire
Andrew F.
5/12/2020
Good afternoon, I recently replaced my 4-pin on my boat trailer. The original 4-pin on it had 7 wires going to it. 1-yellow, 1-green, 2-brown, 3-whites. The new 4-pin only has 4 wires, yellow, green, brown, white. When I spliced them together, I put each color together (therefore there were 3 white wires I spliced to the 1 white wire on the connector and 2 browns to the 1 brown on the connector). When I plugged it in, it all worked but by the time I got my boat to storage and unplugged then replugged it in, I noticed the lights didn't work anymore. Turns out I blew 2-20amp fuses. I wanted to inquire if this could have been caused by my splicings of the different colored wires touching (at the time, they weren't heat shrinked and could have touched the other exposed wires I spliced together in transit to storage), or if it could be overloading the ground wires having 4 wires all connected? Thank you for your assistance.